Zolved community solution
| Zolved community solution |
 new article edit article
|
Mac OS X General DSL and Cable Modem Troubleshooting
This article offers Mac OS X General DSL and Cable Modem troubleshooting information.
Note: If you use AirPort, simplify the troubleshooting procedure by temporarily removing the base station from your network. Set up one computer to connect directly to your DSL or cable modem using the steps below. After re-establishing service to the computer, see the AirPort section below.
- Check all cables and power supplies
Make sure all the cables related to the modem are plugged in and firmly inserted. This includes the modem's power cord, the cable from the modem to the computer, and the cable from the modem to the outlet. To be sure a connector is properly inserted, disconnect and reconnect it. Check to see if the cables have been cut, chewed, or otherwise damaged.
If you have any hubs or routers, check their cables and power supplies. If you have more than one power supply available for a type of hub or router, try swapping the power supplies. A defective power supply will affect network traffic.
- Reset/power cycle modem hardware
Cycle the power on your DSL or cable modem by turning it off for a few minutes then turning it back on. Some ISPs recommend you unplug the modem's power cord. This is required if the modem does not have a power button. If the modem has a reset button, you can try it before or after cycling the power.
- Check indicator lights on the modem
First, check to see if the DSL or cable modem has a "standby" light or button. Modems may not connect to the Internet when in standby mode. If applicable, be sure the modem is not in standby mode.
> Other indicator lights can provide useful information about cabling connections. A light named "Cable" or "Online," for example, indicates whether the ISP's network is available. A "PC" or "link" light indicates whether the hardware connection between the computer and modem is good. A positive link light almost always indicates that the Ethernet ports on each device are working properly, and thus a positive link light makes it very unlikely that an Ethernet port failure is causing the issue.
Tip: If the lights on your modem vary only between on and off and do not change color, then a "positive" light is one that is on. If the lights on your modem change color, a green light is more likely to mean positive than yellow or red.
If your link light is positive, skip to the Check Network preferences settings section. If there is no link, try modem and Ethernet hardware troubleshooting.
- Broadband modem and Ethernet hardware troubleshooting
If the link light is off after you checked your cables and cycled the power, you need to re-establish the link before continuing. If your computer came with an Apple Hardware Test CD, use it to check for any issues with your hardware. If nothing is found, contact your Internet service provider. They may be able to remotely test your modem to see if it has failed. If nothing is found with the modem, replace the Ethernet cable, since it is the most easily replaced component.
If replacing the Ethernet cable does not establish the link, you will need a third Ethernet device to determine whether the computer or modem is failing to link. The third device could be a simple ("dumb") Ethernet hub with link lights (an inexpensive 10BASE-T hub found at any computer store will do), an Ethernet switch with link lights, another computer, a router, or a wireless base station.
When using a hub or switch to test, simply connect both the computer and modem to the hub or switch, then check the link lights on the hub or switch to see which of the other devices is not connecting. If you use another computer (Mac or PC) to test, check to see if the other computer has an Ethernet link light (many do not). If there is no link light on the computer, set up a file sharing connection to verify connectivity. If you use a router or base station to verify connectivity, connect as instructed in the device's documentation. If the router or base station has link lights, you may use the simple link light test.
Be sure that your software settings are correct, as described in the Check Network preferences settings section below.
If you still cannot connect and your cable modem link light is positive, but you haven't replaced the Ethernet cable yet, substitute a new or known-good Ethernet cable for the one you have been using.
- Check Network preferences settings
Follow the steps in the walkthroughs below to verify your connection settings and that Built-in Ethernet is your primary network interface.
If you still cannot connect and your cable modem link light is positive, but you haven't replaced the Ethernet cable yet, substitute a new or known-good Ethernet cable for the one you have been using.
- Additional steps for AirPort
- After successfully connecting to the Internet with the computer, disconnect the modem from the computer.
- Unplug power cords for both the modem and the base station.
- Connect the base station to the modem.
- Plug the modem back in first, then the base station, and wait for the base station's indicator lights to cycle through their startup routine.
- Start up a computer and try to connect to the Internet using the base station. If you cannot, use the AirPort Setup Assistant (/Applications/Utilities/) to copy your computer's network setting to the base station. If you have an advanced network setup, you may need to use AirPort Admin Utility instead.
- After successfully connecting to the Internet with the computer, disconnect the modem from the computer.
Source: EarthLink
